Clazkee
Badges: 3
Rep:
?
#1
Report Thread starter 9 months ago
#1
I’m struggling with this, any ideas for where I can get help?
0
reply
CoolCavy
Badges: 20
Rep:
?
#2
Report 9 months ago
#2
Hey are you evaluating your own product after a project or evaluating existing products?
0
reply
Clazkee
Badges: 3
Rep:
?
#3
Report Thread starter 9 months ago
#3
Thanks for replying - I have to evaluate my own product but not sure where to start. Worried I’ve left the most important part to the last minute
(Original post by CoolCavy)
Hey are you evaluating your own product after a project or evaluating existing products?
0
reply
CoolCavy
Badges: 20
Rep:
?
#4
Report 9 months ago
#4
(Original post by Clazkee)
Thanks for replying - I have to evaluate my own product but not sure where to start. Worried I’ve left the most important part to the last minute
No worries
Think of it like a conclusion for your project in the same way as you would an essay
The following points are important to cover:
-Final feedback from your target market
-What went well with your project and what didnt go well
-What you would change about your product if you were to do it again
-How your product would be made in industry i.e what processes would it need like injection moulding etc
-Would the materials of your product be changed in industry e.g wood to plastic
-Include manufacture drawings from CAD
-Compare your product to your initial specification and write a final specification

hope that helps
0
reply
Clazkee
Badges: 3
Rep:
?
#5
Report Thread starter 9 months ago
#5
Thanks this is very helpful - thank you for responding
0
reply
CoolCavy
Badges: 20
Rep:
?
#6
Report 9 months ago
#6
(Original post by Clazkee)
Thanks this is very helpful - thank you for responding
No worries feel free to come back if you get stuck
0
reply
Clazkee
Badges: 3
Rep:
?
#7
Report Thread starter 9 months ago
#7
Thank you
1
reply
zeph_r
Badges: 1
Rep:
?
#8
Report 9 months ago
#8
Hi, I am also struggling with this evaluation. However I have already completed those tasks on that list as my teacher also instructed me to do. Yet I have included drawings on how I would improve the product by showing what features I would add and how the new design would work. I have not included any drawings or CAD work on my manufacturing page I was wondering if this is essential to have and If so what are these supposed to show? As I have already showed the processes through diagrams of how they work such as injection moulding.


(Original post by CoolCavy)
No worries
Think of it like a conclusion for your project in the same way as you would an essay
The following points are important to cover:
-Final feedback from your target market
-What went well with your project and what didnt go well
-What you would change about your product if you were to do it again
-How your product would be made in industry i.e what processes would it need like injection moulding etc
-Would the materials of your product be changed in industry e.g wood to plastic
-Include manufacture drawings from CAD
-Compare your product to your initial specification and write a final specification

hope that helps
0
reply
CoolCavy
Badges: 20
Rep:
?
#9
Report 9 months ago
#9
(Original post by zeph_r)
Hi, I am also struggling with this evaluation. However I have already completed those tasks on that list as my teacher also instructed me to do. Yet I have included drawings on how I would improve the product by showing what features I would add and how the new design would work. I have not included any drawings or CAD work on my manufacturing page I was wondering if this is essential to have and If so what are these supposed to show? As I have already showed the processes through diagrams of how they work such as injection moulding.
Your evaluation sounds great then
No they aren't essential but if you have time you may as well put them in.
They should show side, front and top views of your product on your chosen software e.g. 2D design with dimensions. The point of these drawings is that rarely are designs manufactured in the UK. If your design was sent to a factory in China they would need the dimension sheet in order to create your product as specified
0
reply
X

Quick Reply

Attached files
Write a reply...
Reply
new posts
Back
to top
Latest
My Feed

See more of what you like on
The Student Room

You can personalise what you see on TSR. Tell us a little about yourself to get started.

Personalise

University open days

  • Norwich University of the Arts
    Postgraduate Open Day Postgraduate
    Thu, 23 Jan '20
  • SOAS University of London
    Development Studies, Interdisciplinary Studies, Anthropology and Sociology, Languages, Cultures and Linguistics, Arts, Economics, Law, History, Religions and Philosophies, Politics and International Studies, Finance and Management, East Asian Languages & Cultures Postgraduate
    Sat, 25 Jan '20
  • University of Huddersfield
    Undergraduate Open Day Undergraduate
    Sat, 25 Jan '20

How many universities have you heard back from?

0 (75)
14.94%
1 (69)
13.75%
2 (65)
12.95%
20.52%
20.32%
5 (88)
17.53%

Watched Threads

View All
Latest
My Feed